0e3c51b72b503594e645228f32895f16

How Loud Is a 500 kW to 2000 kW Generator Set, and What Does 'Soundproof' Actually Mean?

'Soundproof' is not a certified rating — the actual specification a hospital or commercial building should ask for is a measured dB(A) figure at a defined distance and load, since the same generator can sit anywhere from the mid-70s to the high-90s in decibels depending purely on which enclosure type it ships in. Getting this distinction right before ordering avoids the common problem of a technically compliant generator that still fails a building's acoustic requirement once installed.

Noise Varies by Enclosure, Not Just by Model

MPMC's own documentation places its containerised silent-type range from as low as 83.4 dB(A) at 1 metre at 75% load on the MCLS1250 SC up to 98 dB(A) at 1 metre at 75% load on an MCLS2000 open-type unit of comparable capacity — the same underlying engine and alternator platform, with enclosure type accounting for the majority of that 15 dB(A) spread. This is why a hospital or commercial buyer should specify the enclosure type explicitly rather than assuming a given power rating comes with a fixed noise level.

0e3c51b72b503594e645228f32895f16

MPMC super-silent containerised generator sets, part of a documented deployment demonstrating the platform's acoustic enclosure design.

Enclosure Type

Series

Typical Noise Profile

Best Suited To

Open Type

OE

No acoustic enclosure; highest noise output

Fixed installations away from occupied buildings

Economic Type

SE

Basic enclosure, moderate attenuation

Cost-sensitive standby duty, non-sensitive sites

Silent Type

SR2

Noise reduction to 35 dB(A) or below at rated conditions

Noise-sensitive commercial and light-industrial sites

Containerized Super Silent (SC)

SC

83.4-91 dB(A) @1m @75% load depending on model

Hospitals, data centres, and buildings near occupied space

Rental Type

SR (AU/EU)

Super-silent containers to AU/EU rental standard

Temporary hospital or commercial standby contracts

Two Documented Buildings, Two Different Measurement Points

MPMC's 4 MW hospital critical-load backup installation in New Zealand documents 85 dB(A) at 1 metre at full load in a 40HC super-silent container, while a separate 3 MW commercial buildings project, also in New Zealand, documents 75 dB(A) at 7 metres at 100% load using Doosan DP222LC engines in 20HC super-silent containers — a useful reminder that a noise figure is only meaningful alongside the distance it was measured at, since a lower dB(A) figure at a longer distance is not automatically a quieter machine than a higher figure measured close to the enclosure.

Project

Building Type

Capacity

Noise Rating

Measurement Point

Hospital Critical Load Backup, New Zealand

Hospital

4 MW

85 dB(A) @100% load

1 metre from enclosure

Commercial Buildings, New Zealand

Commercial

3 MW

75 dB(A) @100% load

7 metres from enclosure

Af97f39768935420c5c94db572c6d2b1

MPMC silent and economic-type generator sets side by side, illustrating the enclosure difference behind MPMC's noise ratings.

How the Rating Is Actually Verified

Every containerised unit passes through full-load testing at 0%, 25%, 50%, 75%, 100%, and 110% of rated output inside a CNAS-certified test room, and the noise figures MPMC publishes are measured during this process rather than estimated from the enclosure's design specification — meaning a buyer can request the actual test record for their specific unit rather than relying on a catalogue figure that may reflect a best-case build.

Specifying the Right Enclosure for a Hospital or Commercial Site

A hospital's acoustic requirement is usually driven by proximity to wards or outdoor patient areas, while a commercial building's requirement more often comes from a local noise ordinance measured at the property line rather than at the enclosure itself — meaning the correct comparison point (1 metre versus a longer property-line distance) should be established with the acoustic consultant or local authority before the enclosure type is finalised, since specifying against the wrong distance can result in an enclosure that is quieter than required, at unnecessary cost, or louder than compliant.

Questions to Ask About Generator Set Noise Ratings

• Request the dB(A) figure alongside the exact measurement distance and load percentage it was taken at

• Confirm which enclosure type (SC, SR2, or rental super-silent) the quoted noise figure applies to

• Ask for the factory noise test record for your specific unit, not a general catalogue figure

• Establish whether your acoustic requirement is measured at the enclosure or at a property line

• Confirm noise performance at your actual expected operating load, not only at 100% or 75%

• Request a documented reference project with a comparable noise requirement and measurement method

https://www.mpmc-china.com/
MPMC Powertech Corp.

Leave a Reply

Your email address will not be published. Required fields are marked *